PRODUCT UPDATES
	L354-0822 Soldering/Desoldering Handle
3710 Riverside Drive Crystal Lake,  IL   60014 800-662-6099 815-459-0355 Fax: 815-459-0442
BACK	This hand held soldering handle is a new design that will give you the widest possible range of electrode positions and sizes allowing you to solder in locations you only dreamed of getting into before.
	Features: •    Includes 1 1/2”  carbon and 1 1/2” alloy steel electrodes •    Cables Are Not Included, Optional. •    Will silver solder brushes to steel commutator end frames •    Will get inside field cases to silver solder brushes to field coils •    The electrode holders are movable which gives you maximum range and adjustment of the electrode location. •    All parts are serviceable and easily replaceable •    You can make or use your old cables and save a major expense •    Ceramic and cork insulation allows for much cooler use •    Can be powered by battery using our W504-0007-Z Foot Switch or by your old Hot Spot, Resistance         Solder Power Supply or even a Spot Welder.  We recommend a rating of 2500 Watts for the power supply when silver soldering. •    Can operate with a wide range of electrodes, carbon or alloy steel, which gives you greater flexibility.          SHAPE YOUR ELECTRODES TO YOUR SPECIFIC NEEDS. •    The most versatile solder and silver soldering tool I have ever seen. •    Many different size electrodes and holders are available.  See the following page. •    Spring Loaded Handle for easy operation •    Works well on rotor slip ring leads if you want to silver solder them Power Sources: •    A 12 or 24 volt battery with our W504-0007-Z foot switch •    E204-2935-1 Triton Transformer but requires changing the connector size and could not be used for         silver soldering as the 100 Watts would not be high enough.  We recommend the L354-0820-5/32  which is the smallest size electrode for this transformer. •    Old Ace, IPM, Luma, Rebuilders Supply and Wenesco power units with the three connector posts. •    Spot Welder with the adaptation to your tip connection •    Rebuilder Supply Power Unit does not have enough power for silver soldering.  This would be the  units with chicken wire on top. Notes: 1    Remember, you can use your old cable or make your own if they are 4 GA or larger in size.   Saves Money! 2    There is no benefit to running the power supply at the highest heat range.  This will only reduce the life of the electrodes. 3    The electrode should not get red more the 1/4” up from the weld or you are wasting the heat that             should be directed into the weld or solder joint.  Back off the foot switch until the electrode turns black again.  Then step on it again and you will have better results...(cycle the heat) 4    When silver soldering brush leads to the commutator end frames using R059-0175 Ribbon Silver             Solder, we recommend using a light coating of L304-9702-0 Flux and folding over the Ribbon Silver Solder, so you are using a double thickness for good absorption in the brush lead. 5    Use Heat Transfer Compound for the connections between the cable and handle contacts, like you use on rectifier in alternators. 6    Use a High Temperature Lubricant and an Anti-Seize Compound like our S109-2000 or equivalent on all the threads in the electrode holders to make future bolt removal easier. 7    For silver soldering brushes on a commutator end plates, put the carbon electrode on the steel and the alloy steel electrode on the brush lead. OPTIONS & SERVICE PARTS: L354-0820-1    Complete Handle Assembly Only-No electrode holder, electrode or cable        L354-0820-2    Single Arm Only (1)                             L354-0820    Basic Tool L354-0822 with 5’ of #4 welding cable             L354-0820-1/2    1/2” Electrode Holder Kit, (set of 2), for alloy steel & copper coated electrodes   L354-0820-3/8    3/8” Electrode Holder Kit, (set of 2), supplied with carbon electrodes        L354-0820-5/32    5/32 Electrode Holder Kit, (set of 2), supplied with carbon electrodes   L354-0821    5 Feet of #4 Welding Cable with connections, Qty of 2 L354-0820-10    1/2” Copper Coated, High Density Carbons, Set of 2               L354-0820-11    1/2” Alloy Steel Tip, Set of 2                          L354-0820-12    3/8” High Density Carbons, Set of 2                       L354-0820-13    5/32” High Density Carbons, Set of 2 L354-0820-3    Spring & Attaching Kit: contains spring bolt, lock nut & insulators